MSP430
A 16-bit mixed-signal microcontroller family designed for very low power use.
MSP430 is a family of mixed-signal microcontrollers from Texas Instruments, launched on 14 February 1992. Its 16-bit CPU targets embedded work where power draw and cost matter, and the line now spans more than 550 device types.
- Introduced 14 February 1992 by Texas Instruments
- 16-bit CPU, little-endian, von Neumann memory layout
- More than 550 device types in the family
- Up to 25 MHz; simple register ops take one cycle
- MSP430X extends addressing to 20 bits and 1 MB
What it is
MSP430 is a broad family of mixed-signal microcontrollers from Texas Instruments. Each part pairs a 16-bit processor with analogue and digital peripherals on one chip, so a single device can measure a sensor, run code and drive a display. The design brief was low power, low cost and embedded use. The family appeared on 14 February 1992 and has grown to more than 550 distinct types, ignoring package options. Memory varies widely, from tiny 0.5 KB parts up to 512 KB of flash or 256 KB of FRAM, with as much as 66 KB of RAM. Clock rates reach 25 MHz.
How it came about
Texas Instruments introduced the family on 14 February 1992. The earliest members, the MSP430C3xx generation, drew roughly 400 µA per MHz and dropped below 2 µA in their lowest power state with the basic timer and LCD driver still running. Later series pushed those figures down further. The line expanded to cover hundreds of variants, and an extended form called MSP430X was added to lift the addressing limit of the original design.
Inside the chip
The CPU follows a von Neumann layout, meaning program code and data share one address space. Memory is byte addressed, with two bytes joined little-endian into a 16-bit word. Sixteen 16-bit registers are provided: R0 holds the program counter, R1 the stack pointer, R2 the status register, and R3 acts as a constant generator that always reads zero. R4 to R15 are free for general use. Only 27 instructions exist, most in byte and word forms. A simple register-to-register operation completes in one cycle, while indexed forms can take up to six. Up to seven low-power modes are available, and the quickest parts wake in under 1 microsecond.
How it was made
No process node, wafer fab or transistor count is given for these parts. Devices ship in many packages, and most can be programmed in the circuit through JTAG (four-wire or Spy-Bi-Wire), a bootstrap loader over UART such as RS-232, or USB where the chip supports it. Older EPROM and mask ROM versions exist, and some families omit the bootstrap loader entirely.
Where it went
The chips appear in small embedded products that must run for long periods on limited power. One documented example is a glucose meter, the Aktivmed GlucoCheck Comfort, driven by an MSP430FG438. Texas Instruments also supplied experimenter boards, including a larger version and a compact USB-format one. On-chip blocks such as timers with pulse-width modulation, watchdog, USART, SPI, I²C, analogue-to-digital converters, comparators, op-amps, a 12-bit DAC, an LCD driver, hardware multiplier, USB and DMA cover most of what such products need.
Versions and family
The family spans generations from the early MSP430C3xx through to the MSP430FR5xx, which uses FRAM rather than flash and writes non-volatile data quickly without extra power. MSP430X extends the register and address width to 20 bits, opening up to 1 MB of memory while keeping the same instruction set. The '5xx and '6xx lines rework the address map, reserving the first 4 KB for peripherals and offering up to 16 KB of RAM. Port counts and register layouts also differ between families.
Why it matters
With more than 550 types, the family became a standard choice for battery-powered embedded work. Its combination of analogue circuitry, simple 16-bit code and very low sleep current let designers replace several chips with one. The FRAM variants added fast, low-energy non-volatile storage. The architecture also proved easy to learn, with a small instruction set and consistent peripheral addresses across models.
Problems and reception
The design has clear limits. There is no external memory bus, so code and data must fit in on-chip storage, capped at 512 KB of flash and 66 KB of RAM. That rules out jobs needing large buffers or lookup tables. Although a DMA controller is present, moving data off the chip is awkward because no DMA output strobe is provided. Some newer parts bend the rules on 8-bit and 16-bit peripheral access.



Questions people ask about MSP430
What is the MSP430?
It is a family of mixed-signal microcontrollers from Texas Instruments. Each chip combines a 16-bit processor with analogue and digital peripherals, aimed at embedded products where power use and cost are the main constraints. The family launched in February 1992.
Why is it known for low power?
Parts offer up to seven low-power modes. The FR5xx generation draws around 100–120 µA per MHz when active and about 500 nA in its lowest state with the real-time clock running. The CPU core itself uses under 32 µA per MHz, and the fastest devices wake in under a microsecond.
What memory do these chips have?
There is no external memory bus, so everything must sit on the die. Depending on the part you get 0.5–512 KB of flash or 0.5–256 KB of FRAM, plus up to 66 KB of RAM. The FRAM versions write non-volatile data quickly and without extra power.
How do you program one?
Most devices can be programmed in-system through JTAG, either full four-wire or the two-wire Spy-Bi-Wire variant. A bootstrap loader over UART (such as RS-232) or USB is also available on many parts, though certain families ship without it.
What is MSP430X?
It is an extension that widens registers and addresses to 20 bits, allowing up to 1 MB of memory instead of the basic 64 KB space. The instruction set stays the same, with a few extra 20-bit operations and a prefix word that stretches any instruction to 20 bits.
Good reading and sources
The facts on this page come from the Wikipedia article "TI MSP430", written by its contributors and used under the CC BY-SA 4.0 licence, and from its Wikidata record (CC0). EveryChip rewrote the text in its own words, with AI assistance, and compares every page with the article to make sure no passage is copied. It may be reused under the same CC BY-SA 4.0 licence with a link back.
It may contain mistakes, and figures change over time. Nothing here is investment or buying advice. If something is wrong, tell us. Last refreshed 2026-11-14.