National Semiconductor PACE
First commercial single-chip 16-bit microprocessor, from National Semiconductor in 1974
PACE, short for Processing and Control Element, was National Semiconductor's single-chip 16-bit microprocessor, announced in late 1974 as the first commercial chip of its kind. It packed the five-chip IMP-16 design, itself drawn from the Data General Nova, onto one die and added a byte mode for 8-bit data such as ASCII text.
- First commercial single-chip 16-bit microprocessor, announced in late 1974
- Single-chip version of the five-chip IMP-16, itself inspired by the Data General Nova
- Ten on-chip 16-bit stack registers that spill to memory on overflow or underflow interrupt
- All instructions are 16 bits wide: 43 instructions, 45 opcodes
- pMOS part needing three supply voltages; the nMOS INS8900 successor ran about 50% faster
What it is
PACE was the first commercial single-chip 16-bit microprocessor, announced by National Semiconductor in late 1974 under the part number IPC-16A. It took the company's five-chip IMP-16 design from 1973 and put it on one die; that architecture had itself been inspired by the Data General Nova minicomputer. Compared with IMP-16, PACE added a byte mode that switched data accesses to 8 bits, which suited ASCII text and other byte-sized work. The chip ran on pMOS logic, the common technology of the day, and shipped in a 40-pin DIP. Its instruction set was microcoded, and the multiplexed bus meant memory accesses took two cycles.
How it came about
National Semiconductor built PACE as a single-chip version of its own IMP-16, a five-chip processor from early 1973 whose instruction set had been modelled on the Data General Nova. The aim was to bring a 16-bit design down to one device at a time when most microprocessors were 8-bit. Announced in late 1974, PACE arrived with second source agreements in place with Signetics and Rockwell Semiconductor, though neither firm ever produced the design. A redesigned nMOS version, the INS8900, followed later and the company gradually reduced emphasis on the line as faster 16-bit parts appeared.
Inside the chip
PACE kept the Nova-like model of four 16-bit registers, but retuned some instructions to work only on accumulator AC0. It added a hardware stack with a hidden pointer that moves on PUSH and PULL, holding ten 16-bit values on chip; the program counter is pushed and pulled on subroutine calls. Pushing past a full stack or pulling an empty one raises an interrupt, so handler code can spill values to main memory and the on-chip stack acts like a cache. A 16-bit Status and Control Flag register carries flags such as CRY, OVF and a separate LINK bit, plus interrupt enables and output pins. Every instruction is 16 bits wide, with a six-bit opcode and an 8-bit address field, so full addresses are built from the base page, the program counter or index registers AC2 and AC3.
How it was made
The part was built with pMOS logic and packaged in a 40-pin DIP, ceramic at first. Because of pMOS it needed three supply rails: +5 V, +8 V and -12 V used as the ground level, with the +3 V level derived from the +5 V line. An external 750 nanosecond clock, about 1.33 MHz, was shaped by the STE chip to the strength the internal logic required. Signals left the chip at +8 V, so most systems added a BTE transceiver to bring bus levels down to TTL for memory and other parts. Address and data shared the same 16 pins, so external hardware had to latch the address between cycles.
Where it went
PACE turned up in systems built around the IMP-16 style of minicomputer architecture in miniature. A working machine normally needed the STE timing chip to drive the clock and the BTE bidirectional transceiver to translate the chip's +8 V signals to TTL levels for SRAM and similar devices. The shared address and data bus also demanded extra latching logic in memory. Its byte mode made it convenient for text handling, and its 16-bit width gave it an edge over 8-bit parts on wider data, for example inside a floating point library, even though raw instruction speed was similar to an Intel 8080.
Versions and family
The direct successor was the INS8900, the same architecture rebuilt in nMOS. That change cut the supply count, moved signal pins to TTL levels so they could talk straight to memory, and let the STE be replaced by a crystal and a 74C04 inverter. A 2 MHz crystal was recommended, lifting instruction times to 8 through 16 microseconds, roughly 50% faster than PACE. The 8900 also corrected several logic bugs, including faults in the stack-full interrupt. PACE itself replaced the five-chip IMP-16, and second source deals with Signetics and Rockwell Semiconductor produced nothing.
Why it matters
PACE was the first commercial microprocessor to put a full 16-bit design on a single chip, showing that minicomputer-style register and stack handling could be shrunk to one device. Its stack overflow interrupt, which let on-chip registers act as a cache over a memory stack, and its separate LINK flag were ideas borrowed from larger machines rather than typical micros. The line did not last long commercially: by the time the improved INS8900 reached customers, faster 16-bit CPUs were arriving and National Semiconductor began to pull back from selling it.
Problems and reception
PACE ran at a brisk 1.33 MHz, but microcoding and the two-cycle bus meant a typical instruction took about 12 to 30 microseconds, roughly the pace of an Intel 8080. Several logic faults were found, notably in the stack-full interrupt, which could call the wrong handler when it overlapped other interrupts; National Semiconductor advised workarounds until the INS8900 fixed them. Interfacing was awkward because of the three supply rails, the +8 V signals and the multiplexed bus, which is why support chips such as STE and BTE were normally required.
Questions people ask about National Semiconductor PACE
What does PACE stand for?
It is short for Processing and Control Element. National Semiconductor also listed the part as IPC-16A. It was a 16-bit microprocessor announced in late 1974 and was the first commercial single-chip design of that width.
Why did a PACE system need extra chips?
The pMOS die ran at +8 V signal levels and needed three supply rails, so the STE chip shaped the external clock and the BTE transceiver translated bus signals to TTL for memory and other parts. The shared address and data pins also meant external logic had to latch addresses between cycles.
How did the on-chip stack work?
A hidden stack pointer moved automatically on PUSH and PULL, and ten 16-bit locations held the top values. Pushing a full stack or pulling an empty one raised an interrupt so handler code could copy values to or from main memory, letting the small on-chip stack behave like a cache.
What was different about the INS8900?
It kept the PACE architecture but used nMOS logic, so it needed fewer supplies, drove TTL levels directly and dropped the STE chip. It fixed bugs in the PACE interrupt logic and, with a recommended 2 MHz crystal, ran about 50% faster, with instructions taking 8 to 16 microseconds.
How fast was PACE in practice?
The clock ran at 1.33 MHz from a 750 nanosecond external signal, but microcode and the two-cycle memory bus meant a typical instruction took about 12 to 30 microseconds, similar to an Intel 8080. Its 16-bit width still helped on wide data such as floating point work.
Good reading and sources
- National Semiconductor PACE on WikipediaEncyclopedia
- More photos on Wikimedia CommonsPhotos
- Wikidata recordOpen data
The facts on this page come from the Wikipedia article "National Semiconductor PACE", written by its contributors and used under the CC BY-SA 4.0 licence, and from its Wikidata record (CC0). EveryChip rewrote the text in its own words, with AI assistance, and compares every page with the article to make sure no passage is copied. It may be reused under the same CC BY-SA 4.0 licence with a link back.
It may contain mistakes, and figures change over time. Nothing here is investment or buying advice. If something is wrong, tell us. Last refreshed 2026-11-14.
Like National Semiconductor PACE
All CPUs and microprocessors
WorldIntersil 6100
A 12-bit CMOS microprocessor that runs the PDP-8 instruction set on one chipCPU · Other · 1975
WorldMOS 6507
A low-cost 8-bit 6502 variant in a 28-pin package with an 8 KB address rangeCPU · Other · 1975
More from National Semiconductor
All of them
🇺🇸 United StatesNational Semiconductor SC/MP
Early 8-bit microprocessor built for low-cost systems and shared-bus multiprocessor useCPU · 8-bit · 1976