PowerPC 600
Early PowerPC processor family for PCs, workstations and embedded gear
The PowerPC 600 series covers the opening two generations of PowerPC microprocessors, spanning 32-bit and 64-bit designs. Engineers at the Somerset Design Center in Austin built them from 1993 onward for Apple, IBM and Motorola, and the line fed into the later PowerPC 700 generation.
- First PowerPC chips for personal computers, from 1993 onward
- Designed in Austin by a joint Apple, IBM and Motorola team
- 601 combined IBM POWER and PowerPC instructions as a bridge part
- 604ev reached 400 MHz on a 250 nm process
- 620 was the first full 64-bit PowerPC implementation
What it is
PowerPC 600 is the name for the first two generations of PowerPC microprocessors, covering both 32-bit and 64-bit parts. The group spans the 601, 603, 604 and 620 lines plus their revisions. Work took place at the Somerset Design Center in Austin, Texas, a site opened in 1992 and jointly staffed and funded by Apple, IBM and Motorola under the AIM alliance. The first member, the 32-bit 601, reached the market in 1993. These chips mattered because they put the new PowerPC instruction set into personal computers, workstations, servers and embedded equipment at a time when the architecture was still being established.
How it came about
Design work on the 601 started in the middle of 1991, and the first prototype silicon appeared in October 1992. The schedule was deliberately tight so the architecture could gain a foothold. IBM shipped the part in RS/6000 workstations in October 1993, and Apple followed in March 1994 with its first Power Macintosh machines. The second generation arrived in December 1994 as the 603 and 604. A 64-bit sibling, the 620, slipped to 1997 and never sold in volume. The whole family was then replaced by the PowerPC 700 line, which appeared in 1997.
Inside the chip
The 601 carried a 32-bit integer unit, a floating-point unit, branch handling, a sequencer and a memory management unit, plus 32 KB of unified level 1 cache and support for an external level 2 cache. It accepted both IBM POWER instructions and most PowerPC ones. Its external interface, the 60x bus, came from Motorola's 88110 and was reused across later parts. The 603 used a four-stage pipeline with five execution units and split 8 KB caches. The 604 went superscalar, dispatching up to four instructions per cycle through a six-stage pipeline with six execution units and out-of-order completion. The 620 widened caches to 32 KB per side and added a 128-bit system bus.
How it was made
IBM produced the 601 on a 600 nm CMOS process, with a 121 mm2 die holding 2.8 million transistors. The 601v shrank to 500 nm and 74 mm2. IBM and Motorola built the 603 and 604 at 500 nm, then moved to 350 nm and 250 nm for later revisions. Motorola made the 620 at 0.5 µm with a 311 mm2 die and 6.9 million transistors, and a later run at 0.35 µm pushed it to 200 MHz. The 604e used five levels of interconnect; earlier parts used four.
Where it went
Apple placed the 601 in its first Power Macintosh systems and IBM in RS/6000 workstations. The 603 went into cheaper desktops such as the Performa 5200 and 6200 lines after its small split cache handled 68K emulation poorly. The improved 603e reached PowerBook laptops, the BeBox, IBM ThinkPad 800 notebooks, Phase5 accelerator cards for the Amiga, LeCroy oscilloscopes, the Iridium satellite network and the Mark 54 Lightweight Torpedo. Apple used the 604 in high-end Power Macintosh models, and IBM used the 604ev in entry-level RS/6000 machines for years. Groupe Bull was the only customer for the 620, in its Escala UNIX systems.
Versions and family
The 601v was a lower-voltage 601 on a finer process. The 603e doubled level 1 caches to 16 KB per side, and the 603ev moved to 350 nm and reached 300 MHz. Freescale later sold the 603e core as G2 inside PowerQUICC II system-on-chip parts, and refined it as e300 for PowerQUICC II Pro and the MPC5200B. The 604e enlarged caches and added a condition register unit, while the 604ev, also called Mach 5, ran at 250 to 400 MHz. A cut-down 602 targeted game consoles, and the 603q was an independent design announced by Quantum Effect Devices.
Why it matters
The family carried the PowerPC instruction set into the market and gave Apple, IBM and Motorola a shared hardware base. The 60x bus outlived the chips that introduced it, appearing in the 603, 604, G3, G4 and Motorola and Freescale PowerQUICC processors. The 603 design became the basis for the PowerPC 750, sold by Apple as the G3. IBM's 6XX and MX buses for multiprocessor systems later grew into the Fabric Bus and GX bus used in POWER4, then GX+ and GX++ in POWER5 and POWER6, and GX also appears in the z10 and z196 System z mainframes.
Problems and reception
The 601 met its goal of launching the architecture quickly. The 603 drew criticism because its 16 KB split cache handled emulated 68K software badly, so Apple moved it out of laptops into budget desktops. The 620 disappointed: it arrived late in 1997, performed below expectations, and was beaten by the cheaper 604e. Volumes stayed tiny, IBM chose to wait for RS64 and POWER3 instead, and the 603q was cancelled after Motorola pulled out of the contract and its designer lacked a PowerPC licence.


Questions people ask about PowerPC 600
What is the PowerPC 600 family?
It is the collective name for the first two generations of PowerPC microprocessors, covering 32-bit and 64-bit designs. The group includes the 601, 603, 604 and 620 lines and their revisions, built for personal computers, workstations, servers and embedded equipment.
Who designed these chips?
A team at the Somerset Design Center in Austin, Texas. The site opened in 1992 and was jointly funded and staffed by engineers from Apple, IBM and Motorola, the three companies behind the AIM alliance.
Why did the 601 support two instruction sets?
It was meant as a stepping stone between IBM's existing POWER architecture and the new PowerPC instruction set. Handling both let IBM and Apple ship machines quickly while software moved across.
What happened to the 64-bit model?
The 620 slipped to 1997, ran slower than hoped and cost more than the 604e that beat it. Almost nobody bought it beyond Groupe Bull, and IBM chose to wait for RS64 and POWER3 instead.
What replaced the family?
The third-generation PowerPC 700 family, which arrived in 1997. The 603 design fed into the PowerPC 750, marketed by Apple as the G3, and the 604ev was dropped by Apple in 1998 in favour of that part.
Good reading and sources
The facts on this page come from the Wikipedia article "PowerPC 600", written by its contributors and used under the CC BY-SA 4.0 licence, and from its Wikidata record (CC0). EveryChip rewrote the text in its own words, with AI assistance, and compares every page with the article to make sure no passage is copied. It may be reused under the same CC BY-SA 4.0 licence with a link back.
It may contain mistakes, and figures change over time. Nothing here is investment or buying advice. If something is wrong, tell us. Last refreshed 2026-11-14.
Like PowerPC 600
All CPUs and microprocessorsMore from Apple
All of them
🇺🇸 United StatesCyrix Cx486
x86 desktop microprocessor competing with Intel 486CPU · x86 · 1993
🇺🇸 United States and 1 moreMwave
IBM digital signal processor for combined audio and telephonyDSP · Other · 1992