PC66
Standard for 66 MHz synchronous memory modules
PC66 refers to SDRAM modules operating at a 66 MHz clock speed. It emerged as part of the industry shift from asynchronous DRAM to synchronous designs in the 1990s. This standard helped define timing requirements for early personal computer memory systems.
- Operates at a 66 MHz clock frequency
- Uses synchronous interface with external clock
- Preceded by asynchronous DRAM technologies
- Part of JEDEC standardized SDRAM family
- CAS latency typically 2-3 cycles at this speed
What it is
PC66 is a designation for synchronous dynamic random-access memory (SDRAM) modules that operate reliably at a clock frequency of 66 MHz. Unlike older asynchronous DRAM, which responded directly to control signals, SDRAM uses an external clock to coordinate its internal operations. This synchronization allows for pipelined commands and higher data transfer rates. The PC66 label indicates compliance with timing standards necessary for stable performance at this specific speed, serving as an early benchmark for module quality before faster standards emerged.
How it came about
In the 1990s, the industry moved back to synchronous operation after years of using asynchronous DRAM. Samsung produced the first commercial SDRAM chip in 1992, with mass production following in 1993. As clock speeds increased, issues arose with modules failing to meet rated speeds. Intel published the PC100 standard to address reliability at 100 MHz, but the naming convention had already taken hold. PC66 became a common identifier for modules verified to work at 66 MHz, preceding the more rigorous PC100 guidelines.
Inside the chip
SDRAM divides memory into independent banks, allowing simultaneous operations and improved concurrency. Commands are pipelined, meaning new instructions can be issued before previous ones finish. For PC66 modules, the clock cycle time is approximately 15 nanoseconds. CAS latency, the delay between a column address request and data output, typically ranges from 10 to 15 nanoseconds. At 66 MHz, this translates to roughly two or three clock cycles. The interface uses control signals like CKE and CS to manage power and command interpretation on the rising edge of the clock.
How it was made
Early SDRAM chips were manufactured using CMOS fabrication processes. Samsung led initial production, followed by other major manufacturers like Hyundai Electronics and Micron. While specific transistor counts for PC66 modules vary by capacity, the underlying technology relied on standard DRAM cell structures. Modules often contained multiple chips, such as eight or nine devices, to achieve widths of 64 or 72 bits. Compliance with JEDEC standards ensured interoperability across different manufacturers and systems.
Where it went
PC66 SDRAM was widely used in personal computers during the late 1990s. It replaced slower asynchronous DRAM and burst EDO DRAM in many systems due to its higher effective bandwidth. These modules were found in desktops and workstations that required reliable memory performance at 66 MHz bus speeds. As processors and chipsets evolved to support faster front-side buses, PC66 was eventually superseded by PC100 and PC133 standards.
Versions and family
SDRAM comes in various speed grades, including PC100 and PC133, which operate at higher frequencies. Double data rate (DDR) SDRAM later introduced transfers on both clock edges. PC66 represents the baseline for this naming scheme, where the number originally indicated the maximum reliable clock speed. Registered SDRAM variants also exist for servers, offering greater scalability than the unbuffered modules typical in consumer PCs.
Why it matters
The introduction of SDRAM and standards like PC66 marked a significant performance improvement over asynchronous memory. It enabled higher bandwidth through interleaved bank operations and pipelining. The PC naming convention, popularized by Intel’s PC100 standard, became a universal shorthand for memory speed and reliability. This shift helped standardize the memory market, facilitating interoperability and driving the adoption of synchronous memory in virtually all modern computers.
Problems and reception
Early SDRAM was sometimes slower than contemporaneous burst EDO DRAM due to added logic latency. However, its ability to interleave operations provided greater overall bandwidth. Some manufacturers initially sold modules labeled as 100 MHz that could not reliably operate at that speed, leading to the creation of stricter standards. PC66 modules were generally accepted as the baseline for stable 66 MHz operation, avoiding the reliability issues seen in some early higher-speed claims.




Questions people ask about PC66
What does PC66 mean in memory specifications?
PC66 refers to SDRAM modules designed to operate reliably at a clock speed of 66 MHz. The number indicates the frequency, and the prefix denotes compliance with industry timing standards for personal computer memory.
How is SDRAM different from older DRAM?
SDRAM uses an external clock signal to synchronize its operations, whereas older asynchronous DRAM responded directly to control inputs. This synchronization allows SDRAM to pipeline commands and interleave access across multiple memory banks for higher performance.
Who established the standards for PC66 memory?
JEDEC, an electronics industry association, adopted the first SDRAM standards in 1993. Intel later influenced the naming convention with its PC100 standard, but PC66 emerged as a common identifier for modules meeting 66 MHz requirements.
Good reading and sources
The facts on this page come from the Wikipedia article "Synchronous dynamic random-access memory", written by its contributors and used under the CC BY-SA 4.0 licence, and from its Wikidata record (CC0). EveryChip rewrote the text in its own words, with AI assistance, and compares every page with the article to make sure no passage is copied. It may be reused under the same CC BY-SA 4.0 licence with a link back.
It may contain mistakes, and figures change over time. Nothing here is investment or buying advice. If something is wrong, tell us. Last refreshed 2026-11-14.
Like PC66
All memory chipsMore from Intel
All of them
WorldMOS Technology 8502
An 8-bit CPU from MOS Technology that powered the Commodore 128CPU · 8-bit
🇺🇸 United StatesRapidCAD
A 486DX in a 386 socket, with a dummy FPU chip to match.CPU · x86
🇺🇸 United StatesTolapai
Intel embedded SoC with Pentium M core and security accelerationSoC · x86