IntelDX4
Clock-tripled i486 CPU with 16 KB cache, at 75 or 100 MHz
IntelDX4 is a clock-tripled i486 microprocessor with 16 KB of level 1 cache, built by Intel. The 75 MHz and 100 MHz versions both appeared in March 1994, and write-back cache models followed from September 1995. It ran at 3.3 V rather than the 5 V used by earlier i486 parts.
- Clock-tripled i486 with 16 KB level 1 cache
- 75 MHz and 100 MHz versions both released in March 1994
- Runs at 3.3 V; a 5 V socket will destroy it
- Write-through parts marked "&E", write-back parts "&EW"
- iCOMP rating: 435 at 100 MHz, 319 at 75 MHz
What it is
IntelDX4 is a microprocessor in Intel's i486 line. It multiplies the external clock three times internally, so a 25 MHz bus gives 75 MHz and a 33.3 MHz bus gives 100 MHz. A 100 MHz part could also run at 2x 50 MHz. It carries 16 KB of level 1 cache, the small fast memory built onto the chip itself. Intel shipped both speed grades in March 1994. The name skips DX3 because of a trademark dispute with Advanced Micro Devices. Although Intel called it IntelDX4, OEMs kept the older i486 naming style. It was sold to OEMs only; the DX4 OverDrive edition could be bought at retail.
How it came about
The DX4 name came out of litigation with Advanced Micro Devices over trademarks, so Intel jumped past DX3 to DX4. Both the 75 MHz and 100 MHz chips were released in March 1994. Write-back cache versions started sampling in September 1995, and Intel expected to switch fully to them in early 1996. Original write-through parts carry a laser-embossed "&E" mark, while write-back-enabled ones are marked "&EW".
Inside the chip
The chip triples its external clock internally, which is how it reaches 75 MHz from a 25 MHz bus and 100 MHz from 33.3 MHz. It holds 16 KB of level 1 cache. Early parts use write-through caching, where writes go straight to main memory; later ones use write-back, where changed data waits in cache until needed. Pin layout is mostly the same as the i486, but the supply voltage is 3.3 V instead of 5 V. OverDrive versions have locked multipliers and can only run at 3x the external clock.
How it was made
Intel made the IntelDX4 itself. The parts run on a 3.3 V supply, unlike the 5 V i486DX and DX2 chips. Putting a DX4 into an unmodified socket destroys the processor. Where a board cannot supply 3.3 V, a voltage regulator module can sit between socket and CPU. The i486 DX4 OverDrive chips have that regulator built in.
Where it went
IntelDX4 went into OEM systems built around the i486 platform. Boards could accept it where they provided 3.3 V, or with a voltage regulator module fitted under the chip. The OverDrive version, aimed at upgrades, had the regulator on the package and was sold through retail stores. Intel's iCOMP index rated the 100 MHz model at 435 and the 75 MHz model at 319.
Versions and family
Two speed grades were offered: 75 MHz using a 3x 25 MHz multiplier, and 100 MHz using 3x 33.3 MHz or 2x 50 MHz. Cache behaviour also split the line, between write-through and write-back parts, distinguished by the laser marks "&E" and "&EW". i486 OverDrive editions of the DX4 had locked multipliers. The Pentium P54CQS follows it in Intel's line.
Why it matters
The DX4 pushed the i486 design to its highest clock rates by tripling the bus speed inside the chip, extending the life of the 486 platform while the Pentium was arriving. Its move to 3.3 V also marked the shift away from 5 V processor supplies, and the OverDrive package made that easier for upgraders by carrying its own regulator.
Problems and reception
The main practical problem was voltage. A DX4 fitted into a socket wired for 5 V will be destroyed, so boards needed 3.3 V support or a regulator module. The naming also drew attention, since IntelDX4 broke with the i486 convention that OEMs continued to use.




Questions people ask about IntelDX4
Why is it called DX4 and not DX3?
Intel skipped the DX3 name because of litigation with Advanced Micro Devices over trademarks. The product was officially called IntelDX4, though OEMs kept using the i486 naming convention for it.
What speeds did it run at?
There were two grades, both released in March 1994: 75 MHz from a 3x 25 MHz multiplier, and 100 MHz from 3x 33.3 MHz or 2x 50 MHz. OverDrive editions had locked multipliers and could only run at 3x the external clock.
Can I put one in an old 486 board?
Only if the board supplies 3.3 V. The chip is mostly pin-compatible with the i486 but needs the lower supply, and a 5 V socket will destroy it. A voltage regulator module between socket and CPU can help on some boards.
What is the difference between the "&E" and "&EW" markings?
The laser-embossed "&E" marks a write-through cache part, while "&EW" marks a write-back enabled one. Write-back versions began sampling in September 1995, with full production expected in early 1996.
Good reading and sources
The facts on this page come from the Wikipedia article "Intel DX4", written by its contributors and used under the CC BY-SA 4.0 licence, and from its Wikidata record (CC0). EveryChip rewrote the text in its own words, with AI assistance, and compares every page with the article to make sure no passage is copied. It may be reused under the same CC BY-SA 4.0 licence with a link back.
It may contain mistakes, and figures change over time. Nothing here is investment or buying advice. If something is wrong, tell us. Last refreshed 2026-11-14.
Like IntelDX4
All CPUs and microprocessorsMore from Intel
All of them
WorldIntel 80386EX
Embedded variant of the 386 with on-chip peripherals, launched in 1994CPU · x86 · 1994