MAX232
RS-232 to TTL level shifter integrated circuit
The MAX232 is an integrated circuit by Maxim Integrated that converts RS-232 serial signals to TTL logic levels. Announced by 1986, it simplified interface design by generating required voltages from a single 5-volt supply.
- Converts RS-232 signals to TTL logic levels
- Operates from a single 5-volt power supply
- Announced by Maxim Integrated no later than 1986
- Replaced the dual-chip MC1488 and MC1489 solution
- Features on-chip charge pumps and external capacitors
What it is
The MAX232 is a specific integrated circuit model produced by Maxim Integrated Products. It functions as a level shifter, converting signals between TIA-232 serial ports and TTL-compatible digital logic circuits. This chip contains two drivers and two receivers, allowing it to handle common communication lines such as transmit, receive, clear to send, and request to send. By using on-chip charge pumps and external capacitors, it generates the necessary high voltage outputs from a single five-volt power source. This design eliminated the need for multiple voltage supplies in devices requiring serial connectivity.
How it came about
Charlie Allen proposed the concept for this device, while Dave Bingham handled the actual design work. Maxim Integrated Products announced the chip no later than 1986. Before its introduction, engineers used two separate chips, the MC1488 transmitter and MC1489 receiver, to achieve similar results. That older solution required both twelve-volt and negative twelve-volt power rails, along with a five-volt supply. The MAX232 consolidated these functions into a single package that operated solely on five volts, solving significant power distribution problems for designers.
Inside the chip
The circuit translates TTL logic inputs into TIA-232 voltage levels, typically around plus or minus 7.5 volts. It accepts inputs up to thirty volts on the receiver side and steps them down to standard five-volt TTL levels. Receivers feature a typical threshold of 1.3 volts with 0.5 volts of hysteresis. A logic zero input becomes a positive voltage between three and fifteen volts, while a logic one becomes a negative voltage in the same range. The reverse occurs when converting from serial to TTL. This bidirectional translation allows digital systems to communicate with standard serial ports without complex external power circuitry.
How it was made
Maxim Integrated Products manufactured the original device. The company is now a subsidiary of Analog Devices. The chip relies on internal charge pumps to create the higher voltages needed for serial communication from a low-voltage supply. External capacitors are required to support these charge pumps. Other manufacturers produce pin-to-pin compatible versions, including Texas Instruments, which uses the MAX232 part number for its own variants.
Where it went
Engineers typically employ the first driver and receiver pair for transmit and receive data lines. The second pair handles control signals like clear to send and request to send. The chip does not have enough channels to manage data terminal ready, data set ready, or data carrier detect lines simultaneously. In many personal computer interfaces, these extra signals are omitted or handled by special cables. If a device requires all control lines, designers may use a second MAX232 or a different member of the family. It remains a standard choice for embedding serial ports in digital hardware.
Versions and family
The MAX232A is a backward-compatible update that supports higher baud rates and uses smaller external capacitors, specifically 0.1 microfarads instead of 1.0 microfarads. The MAX3232 and MAX3232E operate over a broader voltage range from three to 5.5 volts. Maxim also extended the family with the MAX234, which has four transmitters, and the MAX248, featuring four transmitters and four receivers. The MAX316x variant can switch electrically between differential five-volt modes and single-ended RS-232. Competing models include the ICL232, SP232, ST232, ADM232, and HIN232.
Why it matters
This integrated circuit replaced the cumbersome two-chip solution of the MC1488 and MC1489. By removing the requirement for positive and negative twelve-volt supplies, it simplified power design for embedded systems. The ability to generate necessary signal voltages from a single five-volt rail made it highly useful for devices that did not otherwise need multiple power sources. Its widespread adoption established a standard for simple serial interface implementation. Pin-compatible clones from various manufacturers ensured its longevity and availability across the industry.


Questions people ask about MAX232
What is the primary function of the MAX232?
It converts signals from a TIA-232 serial port to levels suitable for TTL-compatible digital logic circuits. It acts as a dual transmitter and dual receiver, handling voltage translation between the two standards.
Why was the MAX232 better than previous solutions?
It replaced the MC1488 and MC1489 chips, which required separate twelve-volt and negative twelve-volt supplies. The MAX232 generates necessary voltages from a single five-volt supply using internal charge pumps.
Can the MAX232 handle all RS-232 signals?
No, it only has two drivers and two receivers. Typically, these handle TX, RX, CTS, and RTS. Signals like DTR, DSR, and DCD usually require a second chip or are omitted in simple applications.
Good reading and sources
The facts on this page come from the Wikipedia article "MAX232", written by its contributors and used under the CC BY-SA 4.0 licence, and from its Wikidata record (CC0). EveryChip rewrote the text in its own words, with AI assistance, and compares every page with the article to make sure no passage is copied. It may be reused under the same CC BY-SA 4.0 licence with a link back.
It may contain mistakes, and figures change over time. Nothing here is investment or buying advice. If something is wrong, tell us. Last refreshed 2026-11-14.
Like MAX232
All analog, power and mixed-signalMore from Maxim Integrated
All of them
🇺🇸 United StatesBlackfin
Hybrid microprocessor and DSP family by Analog DevicesMicrocontroller · RISC · 2000
🇺🇸 United StatesGP5
Analog co-processor for belief propagation and machine learning tasksAI accelerator · Other