Hewlett-Packard Nanoprocessor
An 8-bit control microcontroller with no arithmetic unit, released by HP in 1974
The Hewlett-Packard Nanoprocessor is an 8-bit control-oriented microcontroller that HP released in 1974 under part number 1820-1692. Built in nMOS logic and lacking any adder or subtractor, it handled sequencing and input/output tasks across a wide range of HP equipment.
- 8-bit control-oriented CPU with no ALU and no add or subtract ability
- 11-bit address bus reaches 2048 bytes of ROM, or 512 KB with bank switching
- Sixteen 8-bit registers plus an 8-bit accumulator and a 1-bit Extend flag
- Seven bidirectional control lines, fifteen inputs and fifteen outputs for 8-bit data
- 40-pin ceramic DIP package dissipating less than one watt
What it is
HP's Nanoprocessor, catalogue number 1820-1692, is a small control-oriented processor introduced in 1974. It is an 8-bit device built with nMOS transistors, intended to supervise and sequence operations inside equipment rather than to calculate. The most unusual thing about it is what it leaves out: there is no arithmetic logic unit, so the chip cannot add or subtract. Instead it offers control logic, comparison, and a generous set of input and output lines. HP fitted it into many of its own products. The whole part sits in a 40-pin ceramic dual in-line package and draws under one watt.
How it came about
Hewlett-Packard developed the Nanoprocessor as a control processor for its own equipment and released it in 1974. The design goal was a chip that could run control tasks cheaply and simply, without the cost of full arithmetic hardware. Because it appeared as a standard catalogue part, 1820-1692, other HP divisions could drop it into their instruments and machines. Programs for it were prepared as assembly source and turned into machine code by an assembler and loader program running on an HP 2100 minicomputer.
Inside the chip
The device handles 8 bits at a time and speaks to program memory over an 11-bit address bus, which reaches 2048 bytes of ROM directly and up to 512 KB if bank switching is used. Its working registers are sixteen 8-bit ones plus an 8-bit accumulator. A single Extend bit, labelled E, serves as a carry flag. Alongside the 11-bit program counter there are two 11-bit registers, one holding a subroutine return address and one holding an interrupt return address; each works as a one-level stack. Arithmetic is absent, replaced by a Control Logic Unit and a magnitude comparator. For the outside world it provides seven bidirectional control lines, fifteen 8-bit inputs and fifteen 8-bit outputs.
How it was made
The chip was fabricated using nMOS logic and housed in a 40-pin ceramic DIP. That package kept power dissipation below one watt. No transistor count or process dimension is given for the part.
Where it went
HP deployed the Nanoprocessor across many of its own products, where it acted as the control element rather than the computing engine. Its wide set of data ports and control lines suited instruments and machines that needed to sequence operations and move bytes between blocks. Firmware was written in assembly and prepared on an HP 2100 system before being loaded into the target ROM.
Versions and family
The part is identified by the HP number 1820-1692. Program storage could be the basic 2048 bytes addressed by the 11-bit bus, or expanded to 512 KB through bank switching. No successor or earlier related part is recorded.
Why it matters
By leaving out arithmetic entirely, the Nanoprocessor showed how much of a processor's cost could be stripped away when the job was only control and data movement. It found a home in a broad range of HP hardware during the 1970s, giving those systems a programmable sequencer without a full CPU.
Questions people ask about Hewlett-Packard Nanoprocessor
What kind of chip is the HP Nanoprocessor?
It is an 8-bit control-oriented microcontroller built from nMOS logic. HP released it in 1974 as part number 1820-1692 and used it inside many of its own products to sequence operations and move data rather than to perform arithmetic.
Why can it not add or subtract?
The design omits an arithmetic logic unit altogether. In its place HP fitted a Control Logic Unit and a magnitude comparator, which were enough for control tasks such as testing values and directing flow, while keeping the part small and its power use under one watt.
How much memory can it work with?
Its 11-bit address bus reaches 2048 bytes of program ROM directly. Bank switching extends that to 512 KB. On the chip itself there are sixteen 8-bit registers, an 8-bit accumulator, and 11-bit registers for program count, subroutine return and interrupt return.
How did engineers write software for it?
Programs were written in assembly language. An assembler and a loader running on an HP 2100 minicomputer converted the source into code and loaded it, ready to be placed in the target system's program ROM.
Good reading and sources
The facts on this page come from the Wikipedia article "Hewlett-Packard Nanoprocessor", written by its contributors and used under the CC BY-SA 4.0 licence, and from its Wikidata record (CC0). EveryChip rewrote the text in its own words, with AI assistance, and compares every page with the article to make sure no passage is copied. It may be reused under the same CC BY-SA 4.0 licence with a link back.
It may contain mistakes, and figures change over time. Nothing here is investment or buying advice. If something is wrong, tell us. Last refreshed 2026-11-14.
Like Hewlett-Packard Nanoprocessor
All microcontrollers
🇯🇵 JapanNEC μCOM series
NEC microprocessor and microcontroller family from the 1970s and 1980sCPU · x86 · 1973
🇺🇸 United StatesElectronic Arrays 9002
An 8-bit CPU with on-chip RAM, sold briefly in the mid-1970s.CPU · Other · 1976