Radeon RX 500 series
AMD graphics cards using refined Polaris chips
AMD launched the Radeon RX 500 series in April 2017 as a refresh of its previous generation. These graphics processors use improved manufacturing nodes to achieve higher clock speeds while retaining the existing architecture.
- Launched by AMD in April 2017
- Uses 14 nm and 12 nm FinFET processes
- Based on fourth-gen GCN architecture
- Supports Vulkan 1.3 and DirectX 12
- Transistor counts range up to 5.7 billion
What it is
The Radeon RX 500 series comprises graphics processing units released by AMD in April 2017. This family serves as an iterative update to the preceding RX 400 line. It relies on the fourth generation of the Graphics Core Next architecture. The primary distinction lies in the fabrication process rather than a new core design. By shifting to smaller transistor nodes, AMD enabled these chips to run at higher frequencies. The series includes various models ranging from entry-level options to enthusiast-grade cards.
How it came about
AMD introduced this lineup to extend the life of its Polaris silicon. The company opted against designing a completely new architecture for this cycle. Instead, it focused on refining the existing GCN fourth-generation design. The launch occurred in April 2017, following the RX 400 series. This strategy allowed AMD to offer improved performance through manufacturing gains. The series eventually gave way to the Vega architecture and later the RX 6000 series for original equipment manufacturers.
Inside the chip
These processors utilize the Graphics Core Next microarchitecture. Most chips in the range are built on the Polaris 20, Polaris 11, or Polaris 12 dies. A high-end variant uses the Polaris 30 chip. The instruction set remains identical to the previous generation. Support extends to modern graphics APIs including Vulkan 1.3 on Linux and Windows for newer cores. Direct3D 12 and OpenGL 4.6 are also supported. Display outputs include HDMI 2.0b and DisplayPort 1.4 with high bit rate support.
How it was made
Fabrication involves multiple foundries and process nodes. Older third-generation GCN chips use a 28 nm complementary metal-oxide-semiconductor process from TSMC. The main Polaris dies are manufactured on a 14 nm FinFET node. This technology was developed by Samsung Electronics and licensed to GlobalFoundries. The Polaris 30 variant utilizes an optimized 12 nm FinFET process from the same partners. Transistor counts vary significantly, from 690 million for smaller dies to 5.7 billion for the largest chips.
Where it went
These graphics cards target personal computers and gaming systems. They handle rendering tasks for desktop environments and video games. The hardware supports high dynamic range colour via HDR10. Resolutions up to 4096 by 2304 pixels are possible through Dual-Link DVI connections. Some cards with VGA ports were marketed primarily in Eastern Asia. The series provides a balance of cost and performance for mid-range gaming rigs.
Versions and family
The family includes several distinct tiers. Entry-level models include the Radeon 520, 530, and RX 540. Mid-range options consist of the RX 550, RX 560, and their X variants. High-end cards feature the RX 570 and RX 580, also available in X versions. The enthusiast segment is represented by the RX 590, which uses the 12 nm Polaris 30 die. Each tier corresponds to a specific chip configuration and transistor budget.
Why it matters
This series demonstrated how process shrinks can boost performance without architectural changes. It allowed AMD to remain competitive in the mid-range market during its lifecycle. The reuse of the Polaris design helped control development costs. Driver support continues, although updates have become less frequent over time. The series bridged the gap between the initial Polaris launch and the subsequent Vega generation.
Questions people ask about Radeon RX 500 series
What architecture does the RX 500 series use?
The series uses the fourth generation of the Graphics Core Next architecture. It is the same microarchitecture found in the preceding RX 400 series, but manufactured on improved process nodes.
Which companies manufactured these chips?
The chips were produced by TSMC, Samsung Electronics, and GlobalFoundries. TSMC handled older 28 nm designs, while Samsung and GlobalFoundries produced the 14 nm and 12 nm FinFET variants.
Does it support modern graphics APIs?
Yes, the series supports Vulkan 1.3 on Linux and newer Windows drivers. It also supports Direct3D 12, OpenGL 4.6, and OpenCL 2.1, ensuring compatibility with modern software and games.
Good reading and sources
- Radeon 500 series on WikipediaEncyclopedia
- More photos on Wikimedia CommonsPhotos
- Wikidata recordOpen data
The facts on this page come from the Wikipedia article "Radeon 500 series", written by its contributors and used under the CC BY-SA 4.0 licence, and from its Wikidata record (CC0). EveryChip rewrote the text in its own words, with AI assistance, and compares every page with the article to make sure no passage is copied. It may be reused under the same CC BY-SA 4.0 licence with a link back.
It may contain mistakes, and figures change over time. Nothing here is investment or buying advice. If something is wrong, tell us. Last refreshed 2026-11-14.